Author: Hassanzadegan, H.
Paper Title Page
WEPP014 A Report on Developments of the BCM and BPM Pickups of the ESS MEBT 532
  • S. Varnasseri, I. Bustinduy, A. Conde, J. Martin, A. Ortega, I. Rueda, A. Zugazaga
    ESS Bilbao, Derio, Spain
  • R.A. Baron, H. Hassanzadegan, T.J. Shea
    ESS, Lund, Sweden
  In the framework of the Spanish In-Kind Contribution (IKC) to the construction of the European Spallation Source (ESS-ERIC), ESS-Bilbao is in charge of providing some key systems for the accelerator. In this paper, design and pre-delivery measurements of non-interceptive devices of MEBT (e.g Beam Position Monitor pick-ups, shielded ACCT and FCT) are reported. Overall there are 8 BPMs distributed in MEBT, which 7 of them are used for the beam position and phase measurements and one BPM is used for the fast timing characterization. The latter is used mainly to characterize the partially chopped bunches and rise/fall time of the Beam Chopper. Furthermore there are two ACCTs, one just attached to the beam dump and the other at the last raft of the MEBT. One FCT combined with the second ACCT gives the complementary information on the fast timing characteristics of the beam pulses.  
DOI • reference for this paper ※  
About • paper received ※ 02 September 2019       paper accepted ※ 10 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
WEPP015 ESS Beam Position and Phase Monitor System 536
  • R.A. Baron, H. Hassanzadegan, A. Jansson, H. Kocevar, K.E. Rosengren, T.J. Shea
    ESS, Lund, Sweden
  • I. Bustinduy, S. Varnasseri
    ESS Bilbao, LEIOA, Spain
  • F. Grespan, M. Poggi
    INFN/LNL, Legnaro (PD), Italy
  • T. Gräber
    DESY Zeuthen, Zeuthen, Germany
  • D. Lipka, S. Vilcins
    DESY, Hamburg, Germany
  The European Spallation Source (ESS) is a neutron facility under construction in Lund, Sweden, and established as an European collaboration between different member countries. The machine is a 2 GeV proton LINAC with a nominal beam current of 62.5 mA, 2.86 ms of pulse length and a bunch repetition rate of 352 MHz. The Beam Position and Phase Monitors (BPM) at ESS were designed to satisfy the specifications for the different beam modes, which span from 5 µs pulse length and 6.3 mA beam until the nominal beam condition. The system is designed for standard beam position measurements for beam trajectory correction and for beam phase measurements for cavity phase tuning, imposing restrictions on the sensor design and electronics architecture. Approximately a hundred BPM’s were manufactured and are being installed by partners in collaboration with ESS. The BPM system comprises a MicroTCA.4 electronics based in COTS AMC and RTM modules with custom FPGA firmware implementation and a custom Front-End electronics. In this work, the system architecture, implementation, performance, and test results are presented and discussed.  
DOI • reference for this paper ※  
About • paper received ※ 04 September 2019       paper accepted ※ 09 September 2019       issue date ※ 10 November 2019  
Export • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)